Rockford, MI

Club member tuneup, furnace is 21 years old, certain parts are showing wear and deterioration from age. Checked flame sensor, spark igniter, motors and filter. Blower motor was showing some concern with the bearings leaking oil. All the other parts of the furnace are operating as they should. The heat exchanger is also showing a lot of wear and corrosion but there is no signs of any cracks yet. Went over repair options and the customer will reach out when he is ready to move forward with options

Performed heating system tuneup. Inducer motor and blower motor amp draws all within proper specification. Tested system safeties and ignition components. Pulled and cleaned flame sensor. Gas pressures and temperature rise are within range. Tested condensate trap and drainage system. Verified the safety and integrity of the heat exchanger. System is operating properly at this time and is in overall good condition. Replace 5” filter. Recommend checking every three to six months. Thank you for having us out!

Furnace tune up. Everything on furnace working properly. I did replace the flame sensor due to it being weak. Everything else working corre

Customers aren’t in hurry they said and wanted to think about it

Tune up. 20 year old furnace. Did noticed Wear on the heat exchanger. I also noticed the draft motor seal is leaking water causing serious rust damage and wear on the board and other components. Flame sensor is also worn. Blower has bearing play and is leaking oil, wheel is also very dirty Everything else on the furnace is acceptable at this time. Customer opted to have an install supervisor out for a quote on replacement options

Club member tune up. Upon inspection I noticed a failure in the heat exchanger, I also noticed the main blower to be leaking oil and have an extreme amount of play in the bearings causing it be loud and loose. Inducer motor is also starting to leak and corroded and getting very hot while running. Igniter is also very worn as well. I called the supply house and they said heat exchangers are not available and have no lead time. After going over repair options she decided to have an install supervisor come out and provide replacement options

We were out today to take a look at the flow tree in the mechanical room. Has been steady at 10 gpm, which used to display 3 gpm. This flow three measures the rate of the hydronic side of the system, so is separate from the geothermal loop. Tried to reduce flow to the hydronic loop, but I was unable to decrease flow below 10. Looked at the circulator and the rated flow rate is 21.7 gpm, so that should have never displayed any lower than 10, unless the pump is larger than the one that used to be on the system. This pump was installed by a different company. Currently consulting with a design engineer from Johnstone Supply. Will be in touch to discuss corrective actions if the engineer recommends it. At this time the system is heating well it is working properly. Thank you for having us out.

Returned to start up heat pump after well pump replacement. Replaced leaking expansion tank for boiler loop. Purged system and restored operation. Well after temperature differential: 51 inlet; 43 out (8 degree delta) Infloor supply temp: 111.2 degrees Infloor return temp: 100.1 degrees System is operating properly at this time. Also test ran the electric boiler, which is also working properly at this time. Thank you for having us out!

We were out today because the geothermal system was not working. Found no water flow coming from the well. Compressor kicks on, but then kicks off after a couple minutes. Thermal switch opens due to no flow. Calling his well company to look into it and also wants a quote on a new geo. Thank you for having us out!

Club member tune up. Flushed water heater replaced worm flame sensor and igniter. Reinstated club membership, everything working correctly

Full System Install Goodman High Efficiency Furnace American Standard Air Conditioner AO Smith Water Heater Chimney Liner and Thermostat 10 year parts and 10 year labor on Furnace and AC

Club member furnace tune up. Cleaned flame sensor and pressure switch tubing. Checked filter. Everything working correctly. No issues

Preset for the 7th of November will call to confirm D. 14.3 seer ac 96% 2 stage Wi-Fi thermostat 10 year labor adding cooper and electric

Finished installing supply diffusers and return air grills as well as sealing and completing a unfinished heat run

$850 extra gets 10 year labor $4500 gets 12 months NINP 6 months is $4275 Cash/cc is $4000

Boiler needs some repairs, Jim is going to reach back out when he decides how he would like to proceed.

Went over options with Karen she needed to discuss with husband will follow up next week

Provided est on heat pump mini splits customer needs to add heat to sunroom gave 2 est one to heat/cool sun room/living room one to provide extra air into kitchen area

We were out today for annual heating maintenance on both furnaces. Performed heating system tuneup. Inducer motor and blower motor amp draws all within proper specification. Tested system safeties and ignition components. Pulled and cleaned flame sensor. Gas pressures and temperature rise are within range. Tested condensate trap and drainage system. Verified the safety and integrity of the heat exchanger. System is operating properly at this time and is in overall good condition. Main floor furnace humidifier was constantly running. Added transformer and properly wired. Working properly now. Performed humidifier maintenance. Replaced water panel, cleaned distribution tray, and tested drain system. Cleaned inside of humidifier, opened damper, and set humidistat to proper humidity setting for the Winter. Thank you for having us out!

Replace furnace and air conditioning system including the following: Goodman Furnace, 96% efficient, 2 Stage Heating Furnace with fixed ECM Blower Motor Goodman Air Conditioner, Up to 13.4 SEER 2.5 ton AO Smith 50 Gallon Power Vent Water Heater Inside- Furnace installed in a drain pan on 2" tall corner "feet" with isolator material on top to help alleviate any potential vibration noise Drain pan equipped with wet switch or drain pipe run to floor drain New return boot with external 1" filter rack with filter cover All new condensate drain pipe with clear, see through, serviceable drain trap with clean out brush(installed on evaporator coil) Install appliance connector on furnace vent, then re-connect vent pipe New copper line set with new control wire Tape all sheet metal joints we connect to with tin pressure tape Custom made sheet metal adapters from existing duct to new equipment New UV Light above evaporator coil Install a power vent 40 gallon water heater in a drain pan with a wa

The customer opted for a Rheem Prestige Series 96% AFUE furnace and a 2.5-ton Rheem RA14 air conditioner, both covered by a 10-year labor and parts warranty. Additionally, they required a propane conversion kit for their gas-powered water heater. The installation will provide high-efficiency heating and cooling with reliable performance. The customer chose to finance the project through Service Finance, allowing for flexible payment options while ensuring their home’s comfort system is upgraded with the latest technology and energy savings.

Installing a new furnace

Furnace inspection. Failed heat exchanger, furnace replacement scheduled

We were out today for our 19.99 tuneup special Replaced failed dual capacitor and verified proper operation. Added 1 pound of R410A to the system to achieve proper Collings charge. Performed air conditioning tuneup. Verified operation of indoor blower and inspected evaporator coil. Tested condensate drain system. Verified proper air flow and temperature differential across coil. Outdoor controls and motors all testing within proper manufacturer specifications. Service disconnect is in good condition and properly fused. Compressor amp draws are within range. Verified condition of outdoor coils. Refrigerant levels are proper at this time. System is in overall good condition. Thank you for having us out!

Found ac pan full of water, troubleshooted system found no immediate cause. Refrigerant levels and filter were in good condition. My only thought is if drain was clogged or filter dirty at the time before the visit. Everything is working correctly After I cleared pan